RPM841-H11 
 
Photo Link Module
 
 
 
8/9 
 
Attached components 
Recommended values
Part symbol
C1
Recommended value
Notice
1礔, tantalum or ceramic
Ex.) TCFGA1A105M8R (ROHM)
Bigger capacitance is recommended with much noise from power supply
R1
2.2&?%, 1/8W
(VLEDVCC=3V)
At LED Emitting Duty=25%
 
 
[LED current set-up method for Remote control mode]
In case of using R1 with different condition from the above, formula is as follows :
LED resistance value : R1[&], LED average consumption current : ILED[mA], Supply voltage : VLEDVCC[V],
minimum necessary of irradiant intensity le1 [mW / sr]
(Including LEDs distribution within ?5deg)
 
R1=166 ?(VLEDVCC1.31) / le17.2
ILED=Duty ?(VLEDVCC1.31) / (R1+5.8)
 
Duty : LED duty at emitting
 
 
 Please set up to be ILED / Duty < 250[mA] (Duty d 25%)
 
 At IrDA Mode, LED current is constantly approximately 50mA.
 
 
(Reference) In case of using R1, typical intensity (le1typ) and maximum intensity (le1max) on
axis are described as below.
   
le1typ=280 ?(VLEDVCC1.31) / (R1+5.8)
 
le1max=560 ?(VLEDVCC1.31) / (R1+5.8)
 
 
Notes
1) LEDVCC (1pin), VCC (6pin)
"
 
Other power source can be used difference between LEDVCC and VCC. 
 
2) Caution in designing board lay-out
To get maximum potential from RPM841-H11, please keep in mind following instruction.
 
"
The line of RXD (4pin) should be connected at backside via through hole close to RPM841-H11 pin lead. Better not to
  be close to photo diode side (7pin).
襎his is to minimize feedback supplied to photo diode from RXD.
"
As for C1 between 6-7 pin should be placed close to RPM841-H11.
"
 
Better to be placed more than 1.0cm in radius from photo diode (pin7 side) and also away from the parts which
  generates noise, such as DC / DC converter.
 
3) Notes
"
 
Please be sure to set up the TX-RC (2pin) and the TXD (3pin) input to be L (under 0.3V) except transmitting data
  (for < 90祍, ON duty d 50%).
"
 
Power down current might increase if exposed by strong light (ex. direct sunlight) at powerdown mode.
"
 
Please use by the signal format at IrDA operating mode which is specified by IrDA Ver1.2 (2.4k to 115.2kbps). There
  might be on error if used by different signal format.
"
 
Please pay attention to the lens carefully.
  Dusts of scratch on the lens may effect the characteristics of product. Please handle it with care.
相关PDF资料
RPM841-H16E4A1 MODULE IRDA 115.2KBPS 7-SMD
RPM870-H14E2 MODULE IRDA 115.2KBPS 8SMD
RPM871-E2 MODULE IRDA 115.2KBPS 8SMD
RPM871-H12E4 MODULE IRDA 115.2KBPS 8SMD
RPM871-H14E2 MODULE IRDA 115.2KBPS 8SMD
RPM872-E2 MODULE IRDA 115.2KBPS 8SMD
RPM872-H12E4 MODULE IRDA 115.2KBPS 8SMD
RPM872-H14E2 MODULE IRDA 115.2KBPS 8SMD
相关代理商/技术参数
RPM841-H11E2A2 制造商:ROHM Semiconductor 功能描述:IRDA TX/RX 0.1152MBPS 3V 8-PIN T/R - Tape and Reel 制造商:ROHM Semiconductor 功能描述:IRDA TX/RX 0.1152Mbps 3V
RPM841-H16 制造商:ROHM 制造商全称:Rohm 功能描述:IrDA Infrared Communication Module
RPM841-H16E4A 功能描述:光纤发射器、接收器、收发器 IRDA IR COMM TOP VIEW W/SHIELD RoHS:否 制造商:Omron Electronics 产品:Transmitters 数据速率:3.5 Gbps 波长:850 nm 最大工作温度: 最小工作温度: 封装 / 箱体: 封装:
RPM841-H16E4A1 功能描述:MODULE IRDA 115.2KBPS 7-SMD RoHS:是 类别:传感器,转换器 >> IrDA 收发器模块 系列:* 产品变化通告:Product Discontinuation 30/Sept/2009 产品目录绘图:GP2W Series 标准包装:1 系列:* 数据速率:115.2kbs(SIR) 电源电压:2.4 V ~ 3.6 V 无效电流,标准值@ 25° C:70µA 通信距离,低功率:20cm 方向:侧视图 工作温度:-40°C ~ 85°C 尺寸:8.3mm x 2.1mm x 1.7mm 标准:IrPHY 1.4 关机:* 包装:Digi-Reel® 其它名称:425-2614-6
RPM841-H16E4A2 功能描述:MODULE IRDA 115.2KBPS 7-SMD RoHS:是 类别:传感器,转换器 >> IrDA 收发器模块 系列:* 产品变化通告:Product Discontinuation 30/Sept/2009 产品目录绘图:GP2W Series 标准包装:1 系列:* 数据速率:115.2kbs(SIR) 电源电压:2.4 V ~ 3.6 V 无效电流,标准值@ 25° C:70µA 通信距离,低功率:20cm 方向:侧视图 工作温度:-40°C ~ 85°C 尺寸:8.3mm x 2.1mm x 1.7mm 标准:IrPHY 1.4 关机:* 包装:Digi-Reel® 其它名称:425-2614-6
RPM841-H16E4A3 功能描述:MODULE IRDA 115.2KBPS 7-SMD RoHS:是 类别:传感器,转换器 >> IrDA 收发器模块 系列:* 产品变化通告:Product Discontinuation 30/Sept/2009 产品目录绘图:GP2W Series 标准包装:1 系列:* 数据速率:115.2kbs(SIR) 电源电压:2.4 V ~ 3.6 V 无效电流,标准值@ 25° C:70µA 通信距离,低功率:20cm 方向:侧视图 工作温度:-40°C ~ 85°C 尺寸:8.3mm x 2.1mm x 1.7mm 标准:IrPHY 1.4 关机:* 包装:Digi-Reel® 其它名称:425-2614-6
RPM851 制造商:ROHM 制造商全称:Rohm 功能描述:IrDA wireless communication transceiver IC (supports Ver.1.0)
RPM851A 制造商:ROHM 制造商全称:Rohm 功能描述:IrDA wireless communication transceiver IC (supports Ver.1.0)